404!
Nothing was found at this location. Try searching, or check out the links below.
Featured Products
-
LI-HSUN
DKS：LATHE WORK-DRIVING CENTER-DKS TYPE (CHANGEABLE TIPS)，DKS301-MT.4
LATHE WORK-DRIVING CENTER-DKS TYPE (CHANGEABLE TIPS)
- Body and center shaft are made of alloy steel with heat and sub-zero treatment.
※ Hardened : HRC60°±1° - Driving centers are either with 6 teeth or 8 teeth design for superseding the driving dogs. It supports the workpiece on the surface for easy setup and rapid machining.
- Applicable for gear hobbing machine.
- Accuracy : 0.008mm
SKU: n/a - Body and center shaft are made of alloy steel with heat and sub-zero treatment.
-
AUTOGRIP
CL-A：Collet Chuck，CL-26A4, CL-30A4, CL-36A5, CL-42A5, CL-42A6, CL-52A6, CL-60A6, CL-60A8, CL-80A8
AUTOGRIPCL-A：Collet Chuck，CL-26A4, CL-30A4, CL-36A5, CL-42A5, CL-42A6, CL-52A6, CL-60A6, CL-60A8, CL-80A8
- PUSH type collet used mainly on turning, CNC, special purpose machines , ect.
- High clamping accuracy, high speed and high rigidity.
- Sealed against swarf, chips and coolant.
- The collet used must accord with DIN 6343.
SKU: n/a
Product Categories
Popular Products
-
CHANDOX
PLVE：3-Jaw Pull Back Power Chuck Fixtures,PLVE-06、 PLVE-08、 PLVE-10
Pull Back Power Chuck Fixture is ideal for machining application on working table, workpiece can be clamped firmly not lift up; it is suitable for heavy cutting as well as the casting and forging machining.
1.Rust-proof for Pneumatic Cylinder：Insid wall of cylinder being rustproof treated; cylinder can work under wet or high moisture circumstances without rusty or seized trouble.
2.Dusts-proof and Waterproof：Dust-proof and Waterproof structure prevents work-chips and coolant water from entering into inside of chuck cylinder to maintain its accuracy and lead to longer service life.
3.Heavy Duty Clamping Design：Collocating hydraulic system to do heavy duty clamping, the chuck structure is steady and wor’t deform.SKU: n/a -
CHANDOX
ST：Stainless Steel Super Thin Chucks,ST-02, ST-03, ST-04, ST-05, ST-06
1. By the compactness comes from “ Light, Thin, Short, Small” designing concept; the chucks are most fitting to hold work pieces for measuring.
2. Just rotate the chuck knob directly for gripping and loosening, A handle is not necessary to be used.
3. The stainless steel body can be placed in electrical discharge machining fluid
4. Jaws can be reversibly used; gripping of various sizes becomes much convenient.
5. 2″ chucks can even grip up to the smallest size of 0.8mm.
SKU: n/a -
AUTOGRIP
3U-K：Pull Lock Power Chuck,3U-205K, 3U-206K, 3U-208K, 3U-210K, 3U-212K
- Pin-Arbor Draw Down type 3-jaw non-thru-hole power chuck.
- High radial gripping force and high accuracy.
- Suitable for heavy machining.
- Can work with the airtight detection device to perform axial position confirm, suitable for the precision of large length size process.
SKU: n/a -
AUTOGRIP
VH:Thru-Hole Stationary 2/3-Jaw Power Chuck,VH2-2204, VH2-2205, VH2-2206, VH2-2208, VH2-2210, VH2-3204, VH2-3205, VH2-3206, VH2-3208, VH2-3210
AUTOGRIPVH:Thru-Hole Stationary 2/3-Jaw Power Chuck,VH2-2204, VH2-2205, VH2-2206, VH2-2208, VH2-2210, VH2-3204, VH2-3205, VH2-3206, VH2-3208, VH2-3210
- STATIONARY CHUCK with two or three jaws for drilling, milling and other machines.
- Specification and size of matching chuck for model VH2-2200 is the same as model 2H-2 ;
- Specification and size of matching chuck for model VH2-3200 is the same as model 3H-2.
- Specification and size of matching chuck for model VH-200 is the same as model 2H ;
- Specification and size of matching chuck for model VH-300 is the same as model 3H.
SKU: n/a
