Recommended Products
DKS：LATHE WORK-DRIVING CENTER-DKS TYPE (CHANGEABLE TIPS)，DKS301-MT.4
LATHE WORK-DRIVING CENTER-DKS TYPE (CHANGEABLE TIPS)
※ Hardened : HRC60°±1°
CL-A：Collet Chuck，CL-26A4, CL-30A4, CL-36A5, CL-42A5, CL-42A6, CL-52A6, CL-60A6, CL-60A8, CL-80A8
CL-A：Collet Chuck，CL-26A4, CL-30A4, CL-36A5, CL-42A5, CL-42A6, CL-52A6, CL-60A6, CL-60A8, CL-80A8
RTS,RTS-T：Rorary air chuck fixtures,RTS-05, RTS-05T, RTS-06, RTS-06T, RTS-08, RTS-10
LOW TORQUE、BULIT-IN CHECK VALVE CONTINUOUS ROTATING
1.When The Chuck is Rotating Continuously: Higher rotation speed to fit with more kind of working, the rotating speed has to be within the max speed limit.
2.Built-in Check Valve: Design with built-in Check Valve. It’s doesn’t need to supply the air continuously and remain low working torque also reduce the air consumption.
3.Dustproof and Drainage Patent Structure: This can prevent the metal chips and coolant get into the chuck inside while processing, and maintain.
4.Integral Pneumatic Cylinder: Connect chuck and built-in cylinder to each other directly; thus enables operation stability. Moreover, it is more convenient for installation and operation since the use of a drawtube and drawbar are no longer necessary.
5.Rustproof Treated Cylinder: The cylinder won’t get rusty and seized even wet or high moisture working environment.
CK：Collet Chucks,CK30A4, CK42A5, CK42A6, CK52A5, CK52A6, CK60A6
1. It is suitable for working with a bar feeder for mass production.
2. The collet chuck needs work with customized-collet.
3. The power chuck needs to be actuated by a hydraulic rotary cylinder and a draw-bar to achieve the clamping action.
4. Suitable for workpieces with small diameters, such as rods, etc.
MO,MOT：3-Jaw Hollow Power Chuck Fixtures,MO–05, MO-04, MO-06, MO-08, MO-10, MO-12, MOT-04, MOT-05, MOT-06, MOT-08, MOT-10
MO,MOT：3-Jaw Hollow Power Chuck Fixtures,MO–05, MO-04, MO-06, MO-08, MO-10, MO-12, MOT-04, MOT-05, MOT-06, MOT-08, MOT-10
With built-in type cylinder, it is ideal for machining application on working table.
1.Rust-proof for Pneumatic Cylinder：Inside wall of cylinder being rustproof treated； cylinder can work under wet or high moisture circumstances without rusty or seized trouble.
2.Dusts-proof and Waterproof：Dust-proof and Waterproof structure prevents work-chips and coolant water from entering into inside of chuck cylinder to maintain its accuracy and lead to longer service life.
3.Benefit of Built-in Cylinder：The cylinder is connected to chuck itself directly for obtaining better stability, less space, and higher machining efficiency.
SE：Super Thin Chucks,SE-02、 SE-03、 SE-04、 SE-04ST、 SE-05、 SE-06
1.By the compactness comes from “ Light, Thin, Short, Small” designing concept; the chucks are most fitting to hold work pieces for measuring.
2.Just rotate the chuck knob directly for gripping and loosening, A handle is not necessary to be used.
3.Chuck body is made of very durable steel.
4.Jaws can be reversibly used; gripping of various sizes becomes much convenient.
5.2″ chucks can even grip up to the smallest size of 0.8mm.
Shop
Showing 97–112 of 522 results
-
-
-
-
AUTOSUPER
AHV：PRECISION HYDRAULIC &ANGLE LOCK HORIZONTAL VISE,AHV-160
The unique features of AHV series provide the users an operation of ease and comfort.
1.Angle-lock type Hydraulic vise model:AHV is mostly suitable for heavy duty cutting on Vertical Machining Center.
2.Semi-spherical segment eliminates jaw lift and workpiece tiltt.SKU: n/a -
AUTOWELL
ALD：LOCKWELL DOUBLE STATION VISE,ALD-60G/HV
1. Double station could clamp two dissimilar workpieces with same force at a time and provides 6 different clamping positions.
2. Clamping Force Equalization (patented) ensures same clamping force to clamp two different size/shape workpieces and avoid deflection and lift.
3. Lockwell Anti-Lift Mechanism (patented) & Automatically Return Mechanism (patented) ensures the workpiece does not deflect and lift.
4. Rigid and tensile ductile iron FCD-60 (80,000PSI) vise body. Slide surface flame hardened to HS65° to maintain the accuracy. S50C jaw-plate has been Carburizing heat treated the hardness to HRC54°.
SKU: n/a -
AUTOWELL
ALQ：MC MECHANICAL LONG POWER VISE,ALQ-160G/HV, ALQ-200G/HV
1. MC Mechanical Long Power vise with large opening and Lockwell Anti-Lift Mechanism is most suitable for VMC & HMC. This vise owns 3 patents and has the honor to get TAIWAN EXCELLENCE 2010.
2. Force Adjustable System (patented) makes the force setting easier & steadier, moreover, it has constant pressure function & over pressure protection.
3. Patented Mechanical Booster is fully sealed against dust, chips and cutting fluid for extended life time.
4. Lockwell Anti-Lift mechanism (patented) ensures the workpiece does not deflect and lift.
5. Unique Out-jaw design increase the clamping capacity.
6. Rigid and tensile ductile iron FCD-60 (80,000PSI) vise body. Slide surface flame hardened to HS65° to maintain the accuracy. S50C jaw-plate has been Carburizing heat treated the hardness to HRC54°.
7. Unique design facilitates the evacuation of chips.
SKU: n/a -
AUTOWELL
AMP：WELLOCK AIR HYDRAULIC POWER VISE,AMP-100, AMP-150, AMP-160, AMP-165, AMP-180, AMP-200, AMP-300
AUTOWELLAMP：WELLOCK AIR HYDRAULIC POWER VISE,AMP-100, AMP-150, AMP-160, AMP-165, AMP-180, AMP-200, AMP-300
1. Most suitable for mass production which need quick machining, such as milling HMC&VMC, expert work station.
2. This vise is adopting the reciprocating pneumatic motor which R&D by inhouse and that employs an air actuated cylinder. Circuiting progressively to make automation, no need the R.F.L unit to filter the moisture, the sole character is superior than other brand in the market.
3. Safety locking mechanism for unexpected termination of air supply. After pneumatic clamping the workpiece will be clamped firmly even without the air supply.
4. Humanistic design. Easy ON/OFF switch control for pneumatic operation. The shifting speed is only 1.5 sec. with safety range: 8mm. The optional electric control for automatic and FMS system is available.
5. AMP are all match vise, you can set up several of AMP together to operate with only one air source supply. 3 operate positions. Six faces of vise body has been ground and pre-set the holding slot, it can be processed vertically without jig block.
6. Even the air source at low pressure 8kg/cm2 which can be achieved super hi-clamping force 90KN, and the 0~90KN clamping force can be adjusted freely by regulator.
7. Unique Out-jaw design increase the clamping capacity.
8. Wellock Semi-spherical segment eliminate deflection and lift.
9. Rigid and tensile ductile iron FCD-60 (80,000PSI) vise body. Slide surface flame hardened to HS65° to maintain the accuracy. S50C jaw-plate has been Carburizing heat treated the hardness to HRC54°.
SKU: n/a -
HOMGE
ANGLE LOCK DRILL PRESS VISE,HDV-100, HDV-130
- ANGLE LOCK MECHANISM produces downward pressure on Jaw during clamping, ensuring that both Jaws are parallel and work is held accurately.
- Built of high tensile (FCD 55) Ductile Iron.
- Slideways and underside of vise are precision ground.
- The Stepped Jaw Plates are hardened to HRC 50º and precision ground.
SKU: n/a -
AUTOWELL
AOM：EXTENSION MC MECHANICAL POWER VISE,AOM-200
1. Extension MC Mechanical Power Vise with large opening and Lockwell Anti-Lift Mechanism is most suitable for BMC & VMC & HMC. This vise owns3 patents.
2.Force Adjustable System(patented)makes the force setting easier & steadier,moreover,it has constant pressure function & over pressure protection.
3.Mechanical Booster(patented)provides a steady clamping force and inside Disc-Spring to shocks and vibrations while operation.
4.. Lockwell Anti-Lift mechanism (patented) ensures the workpiece does not deflect and lift.
5.This vise is suitable for huge or extension workpieces and can be matched.
6. Rigid and tensile ductile iron FCD-60 (80,000PSI) vise body. Slide surface flame hardened to HS65° to maintain the accuracy. S50C jaw-plate has been Carburizing heat treated the hardness to HRC54°.
7.The stationary unit or power unit order is acceptable.
SKU: n/a
Recommended Products
DKS：LATHE WORK-DRIVING CENTER-DKS TYPE (CHANGEABLE TIPS)，DKS301-MT.4
LATHE WORK-DRIVING CENTER-DKS TYPE (CHANGEABLE TIPS)
※ Hardened : HRC60°±1°
CL-A：Collet Chuck，CL-26A4, CL-30A4, CL-36A5, CL-42A5, CL-42A6, CL-52A6, CL-60A6, CL-60A8, CL-80A8
CL-A：Collet Chuck，CL-26A4, CL-30A4, CL-36A5, CL-42A5, CL-42A6, CL-52A6, CL-60A6, CL-60A8, CL-80A8
RTS,RTS-T：Rorary air chuck fixtures,RTS-05, RTS-05T, RTS-06, RTS-06T, RTS-08, RTS-10
LOW TORQUE、BULIT-IN CHECK VALVE CONTINUOUS ROTATING
1.When The Chuck is Rotating Continuously: Higher rotation speed to fit with more kind of working, the rotating speed has to be within the max speed limit.
2.Built-in Check Valve: Design with built-in Check Valve. It’s doesn’t need to supply the air continuously and remain low working torque also reduce the air consumption.
3.Dustproof and Drainage Patent Structure: This can prevent the metal chips and coolant get into the chuck inside while processing, and maintain.
4.Integral Pneumatic Cylinder: Connect chuck and built-in cylinder to each other directly; thus enables operation stability. Moreover, it is more convenient for installation and operation since the use of a drawtube and drawbar are no longer necessary.
5.Rustproof Treated Cylinder: The cylinder won’t get rusty and seized even wet or high moisture working environment.
CK：Collet Chucks,CK30A4, CK42A5, CK42A6, CK52A5, CK52A6, CK60A6
1. It is suitable for working with a bar feeder for mass production.
2. The collet chuck needs work with customized-collet.
3. The power chuck needs to be actuated by a hydraulic rotary cylinder and a draw-bar to achieve the clamping action.
4. Suitable for workpieces with small diameters, such as rods, etc.
MO,MOT：3-Jaw Hollow Power Chuck Fixtures,MO–05, MO-04, MO-06, MO-08, MO-10, MO-12, MOT-04, MOT-05, MOT-06, MOT-08, MOT-10
MO,MOT：3-Jaw Hollow Power Chuck Fixtures,MO–05, MO-04, MO-06, MO-08, MO-10, MO-12, MOT-04, MOT-05, MOT-06, MOT-08, MOT-10
With built-in type cylinder, it is ideal for machining application on working table.
1.Rust-proof for Pneumatic Cylinder：Inside wall of cylinder being rustproof treated； cylinder can work under wet or high moisture circumstances without rusty or seized trouble.
2.Dusts-proof and Waterproof：Dust-proof and Waterproof structure prevents work-chips and coolant water from entering into inside of chuck cylinder to maintain its accuracy and lead to longer service life.
3.Benefit of Built-in Cylinder：The cylinder is connected to chuck itself directly for obtaining better stability, less space, and higher machining efficiency.
SE：Super Thin Chucks,SE-02、 SE-03、 SE-04、 SE-04ST、 SE-05、 SE-06
1.By the compactness comes from “ Light, Thin, Short, Small” designing concept; the chucks are most fitting to hold work pieces for measuring.
2.Just rotate the chuck knob directly for gripping and loosening, A handle is not necessary to be used.
3.Chuck body is made of very durable steel.
4.Jaws can be reversibly used; gripping of various sizes becomes much convenient.
5.2″ chucks can even grip up to the smallest size of 0.8mm.