Recommended Products
DKS：LATHE WORK-DRIVING CENTER-DKS TYPE (CHANGEABLE TIPS)，DKS301-MT.4
LATHE WORK-DRIVING CENTER-DKS TYPE (CHANGEABLE TIPS)
※ Hardened : HRC60°±1°
CL-A：Collet Chuck，CL-26A4, CL-30A4, CL-36A5, CL-42A5, CL-42A6, CL-52A6, CL-60A6, CL-60A8, CL-80A8
CL-A：Collet Chuck，CL-26A4, CL-30A4, CL-36A5, CL-42A5, CL-42A6, CL-52A6, CL-60A6, CL-60A8, CL-80A8
RTS,RTS-T：Rorary air chuck fixtures,RTS-05, RTS-05T, RTS-06, RTS-06T, RTS-08, RTS-10
LOW TORQUE、BULIT-IN CHECK VALVE CONTINUOUS ROTATING
1.When The Chuck is Rotating Continuously: Higher rotation speed to fit with more kind of working, the rotating speed has to be within the max speed limit.
2.Built-in Check Valve: Design with built-in Check Valve. It’s doesn’t need to supply the air continuously and remain low working torque also reduce the air consumption.
3.Dustproof and Drainage Patent Structure: This can prevent the metal chips and coolant get into the chuck inside while processing, and maintain.
4.Integral Pneumatic Cylinder: Connect chuck and built-in cylinder to each other directly; thus enables operation stability. Moreover, it is more convenient for installation and operation since the use of a drawtube and drawbar are no longer necessary.
5.Rustproof Treated Cylinder: The cylinder won’t get rusty and seized even wet or high moisture working environment.
CK：Collet Chucks,CK30A4, CK42A5, CK42A6, CK52A5, CK52A6, CK60A6
1. It is suitable for working with a bar feeder for mass production.
2. The collet chuck needs work with customized-collet.
3. The power chuck needs to be actuated by a hydraulic rotary cylinder and a draw-bar to achieve the clamping action.
4. Suitable for workpieces with small diameters, such as rods, etc.
MO,MOT：3-Jaw Hollow Power Chuck Fixtures,MO–05, MO-04, MO-06, MO-08, MO-10, MO-12, MOT-04, MOT-05, MOT-06, MOT-08, MOT-10
MO,MOT：3-Jaw Hollow Power Chuck Fixtures,MO–05, MO-04, MO-06, MO-08, MO-10, MO-12, MOT-04, MOT-05, MOT-06, MOT-08, MOT-10
With built-in type cylinder, it is ideal for machining application on working table.
1.Rust-proof for Pneumatic Cylinder：Inside wall of cylinder being rustproof treated； cylinder can work under wet or high moisture circumstances without rusty or seized trouble.
2.Dusts-proof and Waterproof：Dust-proof and Waterproof structure prevents work-chips and coolant water from entering into inside of chuck cylinder to maintain its accuracy and lead to longer service life.
3.Benefit of Built-in Cylinder：The cylinder is connected to chuck itself directly for obtaining better stability, less space, and higher machining efficiency.
SE：Super Thin Chucks,SE-02、 SE-03、 SE-04、 SE-04ST、 SE-05、 SE-06
1.By the compactness comes from “ Light, Thin, Short, Small” designing concept; the chucks are most fitting to hold work pieces for measuring.
2.Just rotate the chuck knob directly for gripping and loosening, A handle is not necessary to be used.
3.Chuck body is made of very durable steel.
4.Jaws can be reversibly used; gripping of various sizes becomes much convenient.
5.2″ chucks can even grip up to the smallest size of 0.8mm.
Shop
Showing 401–416 of 522 results
-
AUTOGRIP
RE-A：Compact style Rotary Hydraulic Cylinder with Air Connection and Safety Device,RE-A150, RE-A200K, RE-A200L, RE-A250
AUTOGRIPRE-A：Compact style Rotary Hydraulic Cylinder with Air Connection and Safety Device,RE-A150, RE-A200K, RE-A200L, RE-A250
- For short form, light weight and high speed rotary cylinder. To allow compressed air to be feed from the rear end of the distributor through the rotating union, suitable for vertical lathe.
- Built-in safety check valves, pressure relief valves and proximity sensor.
- Can screw it from the rear end of the cylinder when mounting.
- The drain port should be independently connected to the oil tank to avoid back pressure.
- When used, a little oil mist should be contained.
- The rotary cylinder should not run without air passing through the air port.
- Stroke Detection Type can be customized to Linear Positioning System.
SKU: n/a -
AUTOGRIP
RE-L：Compact style Rotary Hydraulic Cylinder with Coolant Connection and Safety Device
- For short form, light weight and high speed rotary cylinder. To allow coolant to be feed from the rear end of the distributor through the rotating union.
- Built-in safety check valves, pressure relief valves and proximity sensor.
- Can screw it from the rear end of the cylinder when mounting.
- The drain port should be independently connected to oil tank to avoid back pressure.
- The rotary cylinder should not run without liquid through coolant port.
- Stroke Detection Type can be customized to Linear Positioning System.
SKU: n/a -
AUTOGRIP
RE：Compact style Rotary Hydraulic Cylinder with Stroke Control and Safety Device,RE-110, RE-120, RE-130
AUTOGRIPRE：Compact style Rotary Hydraulic Cylinder with Stroke Control and Safety Device,RE-110, RE-120, RE-130
- For short form, light weight and high speed rotary cylinder, suitable for vertical lathe.
- Built-in safety check valves, pressure relief valves and proximity sensor.
- Can screw it from the rear end of the cylinder when mounting.
- The drain port should be independently connected to oil tank to avoid back pressure.
- Stroke Detection Type can be customized to Linear Positioning System.
SKU: n/a -
AUTOGRIP
RH：Hydraulic Rotary Cylinder,RH-100, RH-125, RH-200, RH-65, RH-80
- High speed cylinder with the rotary valve and cylinder body, all made of special light alloy, light-weight.
- Hydraulic rotary cylinder through unique design, the rotary valve enables the inside bearing to get sufficient lubricating and cooling and endure high-speed rotary for longer service life.
- The drain port should be independently connected to the oil tank to avoid back pressure.
SKU: n/a -
AUTOGRIP
RJ：Coolant Rotating Joint,RJ-80, RJ-92
- Coolant joint for high speed, high pressure and medium delivery.
- Usable for oil and water-soluble coolant.
- Seal bushing inside is made of cemented carbide and ceramics, which provide higher wear-resistance.
- The joint should not run without liquid through coolant port.
SKU: n/a -
AUTOGRIP
RK-N：Short type Rotary Hydraulic Cylinder，RK-100N, RK-125N, RK-150N, RK-200N, RK-250, RK75N
- For short form, light weight and high speed rotary cylinder.
- Can screw it from the rear end of the cylinder when mounting.
- The drain port should be independently connected to oil tank to avoid back pressure.
SKU: n/a -
AUTOGRIP
RK：Short type Rotary Hydraulic Cylinder with Safety Device,RK-100, RK-125, RK-150, RK-200, RK-250, RK-75
AUTOGRIPRK：Short type Rotary Hydraulic Cylinder with Safety Device,RK-100, RK-125, RK-150, RK-200, RK-250, RK-75
- For short form, light weight and high speed rotary cylinder.
- Built-in safety check valves and pressure relief valves.
- Can screw it from the rear end of the cylinder when mounting.
- The drain port should be independently connected to oil tank to avoid back pressure.
SKU: n/a -
AUTOGRIP
RL-N：Short type Rotary Hydraulic Cylinder with Coolant Connection,RL-100N, RL-125N, RL-150N, RL-200N, RL-75N
AUTOGRIPRL-N：Short type Rotary Hydraulic Cylinder with Coolant Connection,RL-100N, RL-125N, RL-150N, RL-200N, RL-75N
- To allow coolant to be feed from the rear end of the distributor through the rotating union.
- Can screw it from the rear end of the cylinder when mounting.
- The drain port should be independently connected to oil tank to avoid back pressure.
- The rotary cylinder should not run without liquid through coolant port.
SKU: n/a -
AUTOGRIP
RL：Short type Rotary Hydraulic Cylinder with Coolant Connection and Safety Device,RL-100, RL-125, RL-150, RL-200, RL-75
AUTOGRIPRL：Short type Rotary Hydraulic Cylinder with Coolant Connection and Safety Device,RL-100, RL-125, RL-150, RL-200, RL-75
- To allow coolant to be feed from the rear end of the distributor through the rotating union
- Built-in safety check valves and pressure relief valves.
- The drain port should be independently connected to oil tank to avoid back pressure.
- The rotary cylinder should not run without liquid through coolant port.
SKU: n/a -
AUTOGRIP
RS-N：Short type Rotary Hydraulic Cylinder with Stroke Control，RS-100N, RS-125N, RS-150N, RS-200N, RS-6520N, RS-6530N, RS-7530N, RS-75N
AUTOGRIPRS-N：Short type Rotary Hydraulic Cylinder with Stroke Control，RS-100N, RS-125N, RS-150N, RS-200N, RS-6520N, RS-6530N, RS-7530N, RS-75N
- For short form, high speed and stroke control.
- With proximity sensor , the movement of the position is easy to adjust and confirm when operating.
- Can screw it from the rear end of the cylinder when mounting.
- The drain port should be independently connected to oil tank to avoid back pressure.
- Stroke Detection Type can be customized to Linear Positioning System.
SKU: n/a -
CHANDOX
RT：Rotary air chuck fixtures ( intermittent operation ),RT-05, RT-06, RT-08
INTERMITTENT OPERATION
Suitable for light cutting
It’s ldeal for dividing or cutting work pieces by mounting the chuck on indexing table or rotary table. The distinctive feature is that chuck rotates with the spindle of indexing table or rotary table.
1.The chuck is designed for intermittently rotate in limited rotary speed with rotary table.
2.Rustproof treated cylinder : The cylinder won’t get rusty and seized even in wet or hign moisture working environment.
3.Integral pneumatic cylinder :Connect chuck and built-in cylinder to each other directly;thus enables operation stability.Moreover,it is more convenient for installation and operation since the use of draw tube and draw bar are no longer necessary.SKU: n/a -
CHANDOX
RTS,RTS-T：Rorary air chuck fixtures,RTS-05, RTS-05T, RTS-06, RTS-06T, RTS-08, RTS-10
LOW TORQUE、BULIT-IN CHECK VALVE CONTINUOUS ROTATING
1.When The Chuck is Rotating Continuously: Higher rotation speed to fit with more kind of working, the rotating speed has to be within the max speed limit.
2.Built-in Check Valve: Design with built-in Check Valve. It’s doesn’t need to supply the air continuously and remain low working torque also reduce the air consumption.
3.Dustproof and Drainage Patent Structure: This can prevent the metal chips and coolant get into the chuck inside while processing, and maintain.
4.Integral Pneumatic Cylinder: Connect chuck and built-in cylinder to each other directly; thus enables operation stability. Moreover, it is more convenient for installation and operation since the use of a drawtube and drawbar are no longer necessary.
5.Rustproof Treated Cylinder: The cylinder won’t get rusty and seized even wet or high moisture working environment.SKU: n/a -
AUTOGRIP
Rubber Grip Collet,RG-42, RG-52, RG-65
- Rubber grip collet for push type or draw type collet chucks.
- Full griping area: high rigidity, more gripping force.
Gripping smoothly: prevent to damage the workpiece. - More accurate than standard spring collets.
Accuracy: With customized rubber grip collet. - Grip Range: ±0.5mm
- Quick change and easy.
- Dust-proof and swarf-proof design.
SKU: n/a -
AUTOGRIP
RV：Hydraulic Rotary Valve,RV-31H, RV-A31H
- Hydraulic Rotary valves is used for clamping the cylinder on the rotary table.
- Through unique design, Rotary hydraulic valves can make the rotary housing be rotated with light force and is free from oil leaking.
- I Type is a single circuit that controls the clamping.
- II Type is a double circuit that separately controls the clamping.
- The drain port of the RV type should be independently connected to the oil tank to avoid back pressure.
SKU: n/a
Recommended Products
DKS：LATHE WORK-DRIVING CENTER-DKS TYPE (CHANGEABLE TIPS)，DKS301-MT.4
LATHE WORK-DRIVING CENTER-DKS TYPE (CHANGEABLE TIPS)
※ Hardened : HRC60°±1°
CL-A：Collet Chuck，CL-26A4, CL-30A4, CL-36A5, CL-42A5, CL-42A6, CL-52A6, CL-60A6, CL-60A8, CL-80A8
CL-A：Collet Chuck，CL-26A4, CL-30A4, CL-36A5, CL-42A5, CL-42A6, CL-52A6, CL-60A6, CL-60A8, CL-80A8
RTS,RTS-T：Rorary air chuck fixtures,RTS-05, RTS-05T, RTS-06, RTS-06T, RTS-08, RTS-10
LOW TORQUE、BULIT-IN CHECK VALVE CONTINUOUS ROTATING
1.When The Chuck is Rotating Continuously: Higher rotation speed to fit with more kind of working, the rotating speed has to be within the max speed limit.
2.Built-in Check Valve: Design with built-in Check Valve. It’s doesn’t need to supply the air continuously and remain low working torque also reduce the air consumption.
3.Dustproof and Drainage Patent Structure: This can prevent the metal chips and coolant get into the chuck inside while processing, and maintain.
4.Integral Pneumatic Cylinder: Connect chuck and built-in cylinder to each other directly; thus enables operation stability. Moreover, it is more convenient for installation and operation since the use of a drawtube and drawbar are no longer necessary.
5.Rustproof Treated Cylinder: The cylinder won’t get rusty and seized even wet or high moisture working environment.
CK：Collet Chucks,CK30A4, CK42A5, CK42A6, CK52A5, CK52A6, CK60A6
1. It is suitable for working with a bar feeder for mass production.
2. The collet chuck needs work with customized-collet.
3. The power chuck needs to be actuated by a hydraulic rotary cylinder and a draw-bar to achieve the clamping action.
4. Suitable for workpieces with small diameters, such as rods, etc.
MO,MOT：3-Jaw Hollow Power Chuck Fixtures,MO–05, MO-04, MO-06, MO-08, MO-10, MO-12, MOT-04, MOT-05, MOT-06, MOT-08, MOT-10
MO,MOT：3-Jaw Hollow Power Chuck Fixtures,MO–05, MO-04, MO-06, MO-08, MO-10, MO-12, MOT-04, MOT-05, MOT-06, MOT-08, MOT-10
With built-in type cylinder, it is ideal for machining application on working table.
1.Rust-proof for Pneumatic Cylinder：Inside wall of cylinder being rustproof treated； cylinder can work under wet or high moisture circumstances without rusty or seized trouble.
2.Dusts-proof and Waterproof：Dust-proof and Waterproof structure prevents work-chips and coolant water from entering into inside of chuck cylinder to maintain its accuracy and lead to longer service life.
3.Benefit of Built-in Cylinder：The cylinder is connected to chuck itself directly for obtaining better stability, less space, and higher machining efficiency.
SE：Super Thin Chucks,SE-02、 SE-03、 SE-04、 SE-04ST、 SE-05、 SE-06
1.By the compactness comes from “ Light, Thin, Short, Small” designing concept; the chucks are most fitting to hold work pieces for measuring.
2.Just rotate the chuck knob directly for gripping and loosening, A handle is not necessary to be used.
3.Chuck body is made of very durable steel.
4.Jaws can be reversibly used; gripping of various sizes becomes much convenient.
5.2″ chucks can even grip up to the smallest size of 0.8mm.